CHERY H138CB6105220BA LOCK CYLINDER
Product Specifications
Product quality
OEM Equivalent Grade
Wholesale price USD
$21.06
Wholesale price CNY
¥142.8
bolt MOQ (Minimal order)
1 pcs
local_shipping Production time
30-45 days
package_2 Shipping Weight:
—
swap_horiz
Application (cross references) 1
expand_more
| CHERY | H138CB6105220BA |
Overview & Operating Principle
▲
The LOCK CYLINDER is an exterior or structural body component responsible for providing the mechanical key interface for a door, ignition, or boot lock system, allowing the lock to be operated by the correct vehicle key. Body components must maintain correct dimensional fit against adjacent panels, weatherseals, and glass to prevent wind noise, water ingress, and aerodynamic drag.
Components in this category are manufactured to OEM-equivalent dimensional standards from the correct substrate material (steel, aluminium, or engineering-grade plastic as specified by the OEM). They are supplied in primer or unpainted finish unless stated otherwise on the individual product page.
Verify the vehicle make, model, year, and body variant (2-door, 4-door, estate, etc.) before ordering. Body components are model-specific and often differ between production year facelifts.
Symptoms & Diagnostics
▲
Visible physical damage — cracks, dents, or corrosion on the component surface.
Wind noise or whistling at speed — indicates a gap at the weatherseal interface caused by a deformed or misaligned panel.
Water ingress into the cabin or boot area — caused by a failed weatherseal or misaligned body component.
Rattling noise from the body area — loose or broken mounting clips or damaged panel attachment points.
Impaired function of associated components (door, bonnet, or boot) due to misalignment caused by a damaged panel.
Logistics & Customs
▲
International HS Code
8708.29
EAEU Customs Code (TN VED)
8708 29 100 0
Typical Net Weight
0.5–8.0 kg
Country of Manufacture
China
Standard MOQ
300 pcs
Production Lead Time
60 days
Always verify the exact 8-digit or 10-digit subheading with your customs broker for the destination country, as tariff schedules and duty rates vary by jurisdiction.
Installation Tips
▲
- Document the current panel gap and flush alignment of adjacent panels before removal using photographs. Use these as a reference for setting up the new component.
- Remove all trim clips, electrical connectors, and weatherseals before unbolting the panel. Many clips are single-use and must be replaced during reassembly.
- Transfer all reusable hardware to the new component — brackets, nuts, clips, and weatherseals — before fitting.
- Offer the new component into position loosely before tightening any fasteners. Adjust all gaps and flush alignment before final tightening.
- Torque all fasteners to OEM specification progressively from the centre outwards to avoid panel distortion.
- Check all related functions after fitting — door closure, boot seal, window operation, and weatherseal compression.
Tools: trim clip removal tools, torque wrench, panel gap gauge, alignment reference marks, paint equipment where required.
Frequently Asked Questions
▲
Are body panels supplied painted or in primer?
Body panels in this catalogue are supplied in primer or substrate finish unless explicitly stated as painted on the individual product page. Painting, preparation, and colour matching are the responsibility of the fitting bodyshop.
Do I need to transfer hardware from the old panel?
Yes. Brackets, nuts, weatherseals, and clips are typically not included with replacement panels. Inspect all hardware for damage before reuse and replace any single-use clips or fasteners.
How does the OEM-equivalent aftermarket unit compare to the genuine OEM part?
OEM-equivalent grade units in this catalogue are manufactured to replicate the current OEM design geometry and material specification. Quality is verified against OEM cross-reference data. When ordering in bulk, confirm with our team that the specification matches the latest OEM revision for your application.
Is white-label or custom packaging available for wholesale orders?
Yes. ok.parts works directly with the manufacturing facility and can accommodate neutral white-label packaging or fully branded packaging with your company logo, part numbers, and barcode. Minimum order quantities and lead times for custom packaging may differ from standard stock. Contact the team via the inquiry form to discuss your specific requirements.
Frequently Replaced Together