Brake Calipers: Types, Remanufacturing and Wholesale Sourcing Guide

A brake caliper is rarely replaced because the casting has worn out. It is replaced because a piston or a slide pin has seized behind a torn rubber boot, because the parking brake mechanism inside it has failed, or because a bleed screw snapped off during service. That is why the same housing is sold three ways - new, remanufactured or as a repair kit - and why offers under one OEM number differ so widely.

This guide covers complete calipers, brackets (carriers) and their repair parts: designs, failures, new versus remanufactured units, the causes of wrong orders, and the numbers registered buyers on ok.parts search for most. Many suppliers list a caliper under the Japanese parts-list name Cylinder Assy, Disc - it is the same part.

65caliper numbers in top 2,650
75%searches from five brand groups
$12-19median front caliper offers
93%visible offers from China

Front right single-piston brake caliper 6RF615124 for the VW Polo sedan

The most-searched caliper on ok.parts: front right 6RF615124 for the VW Polo sedan, here from QUATTROFRENI, the private label of ok.parts - see offers

1. What a Brake Caliper Does

The caliper is the hydraulic clamp of a disc brake: pressure from the master cylinder pushes one or more pistons out of the housing, and the pistons press the pads against the disc. Four details explain most of what follows:

  • The piston seal does two jobs. A square-section rubber ring in a groove of the cylinder bore seals the fluid and, when pressure is released, pulls the piston back a fraction of a millimeter. There is no return spring: a sticking piston leaves the pad on the disc.
  • The dust boot keeps water and road salt out. Once it is torn, piston and bore corrode.
  • The bleed screw sits at the highest point of the fluid chamber so trapped air can escape. This is what makes a left caliper different from a right one.
  • The bracket carries the load. On the common floating design the pads rest in a separate bracket bolted to the knuckle or axle; it takes the braking torque, and the caliper housing slides on two guide pins. The bracket is also called carrier, holder, support or - at Nissan - torque member.

2. Types and Designs

Floating, single piston
Floating, single piston
One piston on the inboard side; the sliding housing pulls the outer pad against the disc. The standard design on passenger cars, front and rear.
Most common
Floating, twin piston
Floating, twin piston
Two pistons side by side press a longer pad. Used on the front axle of vans, pickups and heavier SUVs.
Vans and pickups
Rear with parking brake lever
Rear with parking brake lever
A cable-operated lever turns a screw or ball-ramp mechanism inside the piston. It adjusts itself for pad wear; on most designs the piston is screwed back, not pushed, at a pad change.
Mechanical handbrake
Rear with EPB actuator
Rear with EPB actuator
An electric motor with a reduction gear, bolted to the caliper, drives a spindle inside the piston. The actuator is often sold separately.
Electric parking brake

Shown, in order: front left caliper 4605A861 for the Mitsubishi ASX and Outlander PHEV; twin-piston front right caliper 4401J7 for the Peugeot Boxer and Citroen Jumper built from 2006; rear left caliper 5K0615423, used on the VW Golf and related models; and Toyota's parking brake actuator 4631033010.

The fifth design, not in the photos, is the fixed caliper: the housing is bolted rigidly to the knuckle and has pistons on both sides of the disc. It is stiffer and costlier, found on performance cars and the front axle of some large SUVs and pickups.

Not every rear caliper has a parking brake function. Many SUVs and pickups use a plain rear caliper and a small drum brake inside the disc for parking - see the drum brakes and parking brake cables guide.

Materials

Housing and bracket of most calipers are ductile (nodular) cast iron; aluminum housings are used on fixed calipers and on the rear axle of a number of European cars. Pistons are plated steel or phenolic resin. Phenolic pistons cannot rust and pass less heat into the fluid; steel pistons are tougher but corrode once the plating is damaged.

Rear right disc brake cylinder assembly 4783060080 for the Toyota Land Cruiser 200, complete with bracket

A caliper supplied complete with its bracket and pad retaining spring: rear right 4783060080 for the Toyota Land Cruiser 200 - see offers

3. How Calipers Fail

Seized slide pins

The guide pins of a floating caliper run in greased bores sealed by small rubber boots. When a boot splits or the grease dries out, the pin rusts and the housing can no longer slide. Typical signs: an inner pad worn far more than the outer one, wedge-shaped pads, a pull to one side, a hot wheel. Petroleum-based grease is a classic cause: it swells the rubber bushing fitted to one pin on many calipers until the pin jams.

Sticking or seized piston

Glycol brake fluid absorbs moisture over the years. Water in the fluid, or entering past a torn dust boot, corrodes the bore and a steel piston. A piston that does not retract makes the brake drag: heat, smell, rapid pad wear. One that does not move out reduces braking on that wheel, and the car pulls to the opposite side.

Fluid at the piston boot means the seal or the bore is finished. Bleed screws seize and shear when opened - often the real reason an old caliper is replaced.

Parking brake mechanism

On rear calipers with a lever, the lever shaft seizes or the internal adjuster stops following pad wear, and handbrake travel grows. On electric parking brake (EPB) calipers the motor-gear unit fails or water gets into its connector: a warning lamp, and a brake that will not apply or release. EPB fault codes are manufacturer-specific.

A brake hose that has collapsed internally holds pressure in the caliper and makes the brake drag just like a seized piston. Check the hose before condemning the caliper.

Replace at the same time: the guide pin and boot kit if the bracket is reused, the hose sealing washers, the brake fluid, and the pads if they are tapered or soaked with fluid. Many workshops replace calipers in axle pairs; at least inspect the other side.

Aluminum rear right caliper 7701207694 for the Renault Megane, with parking brake lever and return spring - see offers
Aluminum rear right caliper 7701207694 for the Renault Megane, with parking brake lever and return spring - see offers
Hose port and bleed screw on front caliper 4605A861: both must match the side of the car - see offers
Hose port and bleed screw on front caliper 4605A861: both must match the side of the car - see offers
6RF615124 from above: the cast marks R and 54 match the right side and the 54 mm piston - see offers
6RF615124 from above: the cast marks R and 54 match the right side and the 54 mm piston - see offers

4. New, Remanufactured or Repaired

Repair kit. A seal kit, a piston, a guide pin kit or an EPB actuator restores a caliper whose bore is still clean. Offers at one or two dollars under a caliper number are kits.

Remanufactured caliper. A used original caliper - the core - is stripped, the casting cleaned and re-plated, bore and threads inspected, and the unit rebuilt with new seals, boots and bleed screw and a new or refinished piston, then tested. Remanufactured calipers are mainstream in Europe and North America, also in vehicle makers' own parts programs. They carry a core charge: a deposit paid on top of the price and refunded when the old caliper is returned complete, undamaged and of the same type.

New aftermarket caliper. A new casting assembled from new parts. There is no core to return, which suits importers outside the established core-return networks. Export factories as a rule sell new calipers without a core charge.

Neither route is automatically better. A remanufactured unit depends on the rebuilder and on the core: a pitted bore or a worn thread cannot be plated away. A new unit depends on the foundry, the machining and the rubber. Judge both by the checks in the quality section.

Calipers are safety-critical, and a low-priced offer is not equivalent to the original part until proven. ECE R90 - the UN regulation for replacement pads, discs and drums - does not cover calipers, so there is no approval mark to rely on, only test records and your own inspection.

In North American trade terms a loaded caliper comes with pads and hardware, a semi-loaded one with hardware but no pads. "Padless" in a listing means no pads.

5. Left, Right and Other Sources of Wrong Orders

Left and right are mirror images. On the wrong side a caliper may bolt on, but the bleed screw ends up at the bottom and the air cannot be bled out. Sides are given as seen from the driver's seat. Several makers encode the side in the number:

Brand groupFront left / rightRear left / right
VW / Audi / Skoda / Seat615123 / 615124615423 / 615424
Nissan, newer Renault41011 / 4100144011 / 44001
Hyundai / Kia58110 / 5813058210 / 58230 or 58300 / 58400
Toyota / Lexus47750 / 4773047850 / 47830

Older Renault numbers follow no such rule: 7701207686 is a front right caliper, 7701207693 a rear left one. When in doubt, ask for a photo showing the cast L or R.

Brake size within one model. A model is usually built with two or three disc sizes depending on engine and payload, and caliper and bracket change with them. In the ranking below, 7H0615123A is the VW T5 caliper for 308 mm discs; other T5 versions take different numbers. Order by VIN: see how to find an OEM number.

With or without bracket. Some OEM numbers are the bare caliper, some the complete brake with bracket, and aftermarket suppliers offer both under one number. A bracket also has its own number: 13372780, listed as a caliper support, is a front bracket, not a caliper.

Parking brake version. Rear calipers for a cable handbrake, for an electric parking brake and with no parking function do not interchange. For EPB calipers confirm whether the motor is included; offers titled "EPB actuator" or "servomotor" under a caliper number are the motor alone. The hose connection (banjo bolt or flare nut, thread) must match too.

6. The Most-Searched Numbers on ok.parts

The table is ranked by repeat searches from registered buyers on ok.parts.

Five brand groups account for about three quarters of the searches in this group: VW / Audi / Skoda / Seat and Nissan / Infiniti with about 17% each, Renault / Dacia 16%, Mitsubishi 14% and Hyundai / Kia 11%. GM (Chevrolet, Opel, Buick) and JAC follow with about 6% each, Toyota / Lexus with 4%.

By listing name, about 93% of the searches are for complete calipers and about 4% for brackets; the rest are listed as padless calipers, a name that here also covers EPB parts. The models behind the numbers are high-volume cars and working vehicles - VW Polo sedan, Hyundai Accent, Renault Megane, Nissan Qashqai, Mitsubishi L200, GAZelle Next - not performance cars.

OEM numberBrandPartOffersMedian priceNotes
6RF615124VW / Audi / Skoda / SeatFront right caliper, 54 mm piston23$14.04VW Polo sedan; also Skoda Fabia II, Rapid
C41R923502137GAZRear left caliper11$17.54GAZelle Next 4.6 t
583001R300Hyundai / KiaRear left disc brake assembly49$19.36Hyundai Accent / Solaris (2010-2016 generation)
3504020R1040JACRear right caliper assembly6$30.61JAC Sunray van (Sollers Atlant)
7701207686Renault / DaciaFront right caliper19$12.24Renault Megane II, Scenic II
13372780GM (Chevrolet, Opel, Buick)Front caliper bracket (carrier)37$14.19Opel Astra J, Chevrolet Cruze (aftermarket data)
4100100Q0FNissan / InfinitiFront right caliper, 54 mm piston75$13.66Nissan Note E11, Micra K12 (aftermarket data; confirm by VIN)
581101F000Hyundai / KiaFront left caliper31$14.78Kia Sportage (2004-2010)
410018218RRenault / DaciaFront right caliper19$62.54Renault Megane III, Scenic III, Captur; Dacia Logan / Sandero II, Dokker
4605A201MitsubishiFront left caliper kit53$13.44Mitsubishi L200 / Triton, Pajero Sport
13301189GM (Chevrolet, Opel, Buick)Front left caliper, for 276 mm discs46$13.21Opel Astra J, Chevrolet Cruze and Aveo
41001JD00ANissan / InfinitiFront right caliper, without pads58$14.41Nissan Qashqai / Qashqai+2 (J10), X-Trail
440111AA0ANissan / InfinitiRear left caliper, without pads24$15.15Nissan Murano, Pathfinder (2013-2020), Quest, 370Z
4605A477MitsubishiRear left caliper kit32$9.64Mitsubishi Lancer, Lancer Sportback
KAY02661XMazdaRear right caliper for electric parking brake26$73.48Mazda CX-5
7701207694Renault / DaciaRear right caliper, aluminum, with parking brake lever45$16.13Renault Megane family
7H0615123AVW / Audi / Skoda / SeatFront left caliper, for 308 mm discs29$15.68VW Transporter / Multivan T5
4783060080Toyota / LexusRear right disc brake cylinder assembly24$16.80Toyota Land Cruiser 200 (2008-2016)
6C112553ADFordRear left caliper with parking brake lever24$21.56Ford Transit (2006-2014)
4631033010Toyota / LexusElectric parking brake actuator, left or right55$12.39Recent Toyota Camry, RAV4, Corolla, C-HR, Highlander

Fitment notes name main applications and do not replace a VIN check. The JAC number has a rear left partner, 3504010R1040.

Find suppliers by part number

7. Quality: Castings, Rubber, Plating and Tests

Casting and machining

Housings and brackets are cast in ductile iron; grades such as QT450-10 (Chinese standard) or EN-GJS-450-10 (European) are typical. Ask which grade is used and for the material certificate. Porosity is the main casting defect: in the wrong place it becomes a leak that shows only under pressure. The seal groove geometry sets how far the piston retracts, so a carelessly copied groove gives a dragging brake or a long pedal.

Rubber

Piston seals and boots for glycol brake fluid (DOT 3, DOT 4, DOT 5.1) are made of EPDM. Mineral oil and petroleum grease swell it. SAE J1603 is a common reference standard for disc brake cylinder seals; ask which standard the compound is tested to.

Surface protection

Iron housings are zinc or zinc-nickel electroplated and passivated, or painted; zinc-nickel lasts markedly longer in road salt. Ask for the plating type and the hours reached in neutral salt spray (ISO 9227 or ASTM B117).

Tests to ask about

  • Leak test of every unit at low and at high pressure; a high-pressure test alone misses low-pressure seal leaks.
  • Piston sliding force and seal retraction.
  • Function test of the parking brake lever and adjuster; for EPB units, a run test of the actuator.
  • IATF 16949 certification, the automotive quality management standard.

Incoming inspection

  1. Check the cast side mark and hold the caliper as mounted: the bleed screw must be at the top.
  2. Measure piston diameter and mounting hole spacing against the original.
  3. Hose port and bleed screw must be plugged or capped; an open port means dirt and moisture inside.
  4. The dust boot must sit in its groove all round, not twisted or pinched.
  5. Guide pins must slide smoothly by hand; bolts and a hose fitting must run into the threads by hand.
  6. The parking brake lever must return to its stop under the spring; on EPB units compare the connector with the original.
  7. Compare weights between samples and batches.

See also the quality control guide.

8. Wholesale Buying Notes

A snapshot of offers visible on ok.parts on 7 October 2026 - median offer prices per number, not quotes:

Sub-typeMedian offer priceExamples
Front single-piston calipersabout $12-196RF615124, 41001JD00A, 7H0615123A
Rear calipers, plain or with levermostly about $8-234605A477, 7701207694, 6C112553AD
Rear calipers for EPBabout $50-75KAY02661X
Twin-piston van caliperabout $204401J7
Caliper bracketabout $1413372780

Price spread. Visible offers in this group ran from under $2 to several hundred dollars. The bottom is repair kits and, on EPB numbers, actuators; the top is stock under the vehicle maker's brand. On Renault number 410111495R that mix lifts the median above $60 although unbranded calipers start near $12. Compare like with like: see OEM vs OES vs aftermarket and the counterfeit parts guide.

Suppliers and MOQ. About 93% of the visible offers came from China and 7% from the United Arab Emirates; about 93% were listed by factories, the rest by wholesale companies. Common minimum order quantities were 1, 10, 20, 25, 50 and 100 pieces; most offers are unbranded, neutral-pack parts. See the factory vs trading company guide.

Packaging and freight. Calipers are heavy for their size, so weight drives the freight cost. Ask for strong individual boxes, a sealed bag and plugged ports. Calipers generally fall under HS subheading 8708.30 (brakes and parts); national sub-codes differ, so confirm with your broker. See shipping auto parts from China and Incoterms for importers.

Warranty. Leaks and sticking pistons appear in service, not on the shelf. Agree in writing on the warranty period, the evidence required for a claim and who pays return freight.

Combining an order. Order left and right together, with pads, hoses and guide pin kits. If a number shows no suitable offer, post a buying request.

Post a buying request

9. Frequently Asked Questions

Is a new aftermarket caliper better than a remanufactured one?

Not by definition. A remanufactured unit depends on the rebuilder and the core; a new unit on the foundry, machining and rubber. Ask both for leak-test and corrosion-test evidence.

What is a core charge on a caliper?

A deposit added to the price of a remanufactured caliper, refunded when the old unit is returned complete and undamaged. New calipers are sold without it.

Does a caliper come with the bracket and pads?

It depends on the number and the offer. Many are bare calipers; others include the bracket and guide pins. Confirm the box contents in writing.

Why do offers under one caliper number differ so much in price?

Repair kits, pistons and EPB actuators are listed under the caliper's number at the bottom of the range, genuine-branded stock at the top. Read the offer title before comparing prices.

Can the electric parking brake motor be replaced on its own?

On many models yes: the actuator is bolted to the caliper and has its own part number. Before work the spindle is retracted through the diagnostic service mode; forcing the piston back damages the mechanism.

Related Guides