Control Arms, Bushings and Ball Joints: Technical and Wholesale Sourcing Guide

A control arm is three parts sold under one number: a metal link, one or two rubber-metal bushings and, in most cases, a ball joint. Each can be made cheaply in its own way, and offers under one OEM number can be the complete arm, the bare bushing or the ball joint alone - which is why prices under one number can differ twentyfold.

This guide covers the group as buyers search for it on ok.parts - complete control arms (wishbones), bushings, ball joints and steering knuckles: designs, failure modes, the left-right and version traps behind wrong orders, and what to ask a factory.

Suspension is safety-critical: a failed ball joint or cracked arm can let the wheel fold under the car. The cheapest offer is never automatically equivalent to the original part.

24%of searches: VW / Audi numbers
51%of searches: complete arms
$11-35typical median arm price, Oct 2026
87%of visible offers from China

Aluminum front upper control arm 7L0407021 with two bushings and ball joint

Aluminum front upper control arm 7L0407021 for the VW Touareg, Porsche Cayenne and Audi Q7: two pressed-in bushings and an integrated ball joint - see offers

1. What the Arms, Bushings, Ball Joints and Knuckles Do

The steering knuckle (wheel bearing housing, upright) carries the wheel bearing, the brake caliper and the steering arm. Control arms connect it to the body or subframe and let the wheel move up and down while holding it fore-aft and sideways.

At the body end, bushings - rubber bonded between two metal sleeves - let the arm swing and filter road shock. At the wheel end, a ball joint lets the knuckle steer and tilt.

The number of arms depends on the axle design:

  • MacPherson strut (most front axles): one lower arm per side.
  • Double wishbone: an upper and a lower arm, as on the Touareg / Cayenne front axle shown above.
  • Multi-link: the wishbones are split into separate links. Audi's four-link front axle has two upper and two lower arms per side, each with its own ball joint; BMW's double-joint front axle has two lower arms, a lateral wishbone and a diagonal tension strut.
  • Rear multi-link axles: several simple links with a bushing at each end, usually without a ball joint.

2. Arm Designs and Materials

Stamped steel arm
Stamped steel arm
Pressed and welded sheet steel, the standard on small and mid-size cars. Cheap and tough; weak points are rust and weld quality.
Most common
Forged or cast steel arm
Forged or cast steel arm
A solid one-piece link for heavier cars and SUVs, often with a large rubber or hydraulic bushing.
Heavy duty
Aluminum arm
Aluminum arm
Usually forged on the original part to cut unsprung weight. Must never be straightened after an impact.
Lightweight
Rear link
Rear link
A simple steel rod or pressing with a bushing at each end, for rear multi-link axles.
Multi-link

Shown, in order: stamped lower arm with bolt-on ball joint listed under Chery number 202000470AA; steel tension strut 31126768984 for all-wheel-drive versions of the BMW 3 Series E90 family; aluminum front lower arm 4F0407151A for the Audi A6 C6, which fits both sides; rear link 1K0501529F for the VW Golf V / VI platform.

An arm is offered either complete (bushings pressed in, ball joint fitted) or bare. Some original arms come without a ball joint by design, such as the stamped Tiguan arm 5N0407151.

3. Bushings and Ball Joints

Bushings

TypeHow it worksWhere used
Solid rubber-metalRubber vulcanized between two sleeves twists as the arm movesMost arms and rear links
Voided (directional)Cut-outs make it soft in one direction; pressed in at a marked angleFront lower arms
Hydraulic (hydro-bushing)Fluid-filled chambers damp brake judder and wheel shimmyTension struts and lower arms of larger cars
Truck bushings, spring mountsLarge rubber-metal elements, some laminated with steel platesTorque rods, stabilizers, leaf-spring brackets

A solid-rubber copy of a hydro-bushing looks the same on a photo and costs less. If the original is hydraulic, get written confirmation that the offered part is.

Car makers often sell only the complete arm. Aftermarket brands that list the bushing alone fill that gap, which is why Febest codes such as TABZZE150B are searched directly.

Ball joints

A ball joint is a hardened steel stud with a ball end running in a polymer seat inside a steel housing, greased and sealed by a rubber boot. It is fixed in one of three ways:

  • Integrated: the housing is part of the arm; a worn joint means a new arm. Common on aluminum arms.
  • Press-in: a separate joint pressed into the arm or knuckle.
  • Bolt-on: a flanged joint fixed with two or three bolts (riveted at the factory on some cars).

The stud sits in the knuckle by a taper and nut or by a straight shank and pinch bolt. Taper, stud diameter and thread are where look-alike joints differ.

Bolt-on ball joint offered under Chery number 202000469AA, here with castle nut and split pin - see offers
Bolt-on ball joint offered under Chery number 202000469AA, here with castle nut and split pin - see offers
Front lower arm bushing (rear position) under Febest code TABZZE150B, a Toyota application - see offers
Front lower arm bushing (rear position) under Febest code TABZZE150B, a Toyota application - see offers
Bare bushing offered under BMW tension strut number 31126775971 - see offers
Bare bushing offered under BMW tension strut number 31126775971 - see offers

4. Steering Knuckles

The most-searched number of this whole group is not an arm. 8D0407258AM is the front right steering knuckle of the Audi A4 B5 / A6 C5 / VW Passat B5 platform. Its tall neck reaches up to the two upper arms of the four-link axle, whose ball-joint studs are clamped in the top of the knuckle by a single pinch bolt. That bolt is known for seizing, and knuckles get damaged during removal.

Front right steering knuckle 8D0407258AM for Audi four-link front suspension

Steering knuckle 8D0407258AM: wheel bearing bore on the left, tall neck for the two upper arms on the right - see offers

Knuckles are made of ductile (nodular) cast iron, forged steel or aluminum. Other reasons for replacement are accident damage and a bearing bore worn by a spun bearing. What matters when buying:

  • Bearing fit. Many knuckles take a press-in bearing, and the bore tolerance decides whether it stays put. Aftermarket parts data lists 8D0407258AM with an 82 mm bearing seat, and the same platform also has knuckles for a smaller bearing - measure the old part. See the wheel bearings guide.
  • Side. Left and right are mirrored and never interchange.

Other knuckles with steady demand are 6RU407255A (front left, VW Polo family) and 517152S000 (front left, Hyundai ix35 / Tucson from 2010).

5. How These Parts Fail

Suspension joints set no fault codes; diagnosis is by ear and with a pry bar.

Bushings crack, tear or separate from their sleeves; hydro-bushings also leak, leaving an oily streak. Signs: a clunk when braking or pulling away, vague steering, steering-wheel shimmy under braking, tires wearing on one edge.

Ball joints fail after the boot splits: water gets in, the grease washes out, the seat wears and the stud develops play. Signs: a knock over small bumps, creaking when steering, wandering. In the end the stud can pull out of the housing. A torn boot alone is reason to replace the joint.

Arms bend on curb and pothole strikes - the car then cannot be aligned - and stamped steel arms rust through. Aluminum arms can crack after an impact that leaves no visible bend.

Installation mistakes that look like bad parts

Bushing pivot bolts must get their final torque with the suspension at normal ride height, not with the wheels hanging. Tightened at full droop, the rubber stays twisted and tears early - and the claim comes back to the seller.
  • Voided and hydraulic bushings pressed in at the wrong angle.
  • Old stretch bolts reused, or wheel alignment skipped after the work.

Related wear parts: see the tie rod ends and stabilizer links guide.

6. Left, Right and Look-Alike Versions

1. Left and right. Arms and knuckles are mirrored, and brands number them differently:

BrandPattern in this rankingExample
Hyundai / Kia54500 = left, 54501 = right54500M0000 left
Nissan54501 = left, the opposite545014CL1B left
BMWPairs: odd = left, even = right31126852992 right
VW / AudiBase number: odd = left, even = right5N0407151 left

Some arms fit both sides - the Audi A6 C6 arm 4F0407151A and the Touareg upper arm 7L0407021 - so do not assume a pair exists.

2. Position. Arms of a multi-link corner are easy to confuse by name. BMW calls the diagonal lower arm a tension strut and the lateral one a wishbone; aftermarket lists say "front" and "rear", not always consistently. Match the number, not the name.

3. Material and drive versions. Steel and aluminum arms for the same model are not interchangeable as a rule, and rear-wheel-drive and all-wheel-drive versions often use different front arms and knuckles: the steel tension strut 31126768984 is the xDrive part of the BMW E90 family.

4. What is in the box. Under one arm number, suppliers list the complete arm, the bare bushing and sometimes the ball joint. The short part name shown next to a number on the site is a group label, not a guarantee: GM's own parts list names 95032440 an arm (aftermarket data: front lower arm, Chevrolet Spark), although the site files it under ball joints. Read the offer title, look at the photo and ask for the unit weight.

5. Supersessions and small details. Car makers replace numbers: BMW 31124083312 has been superseded by 31126775960. Arms can also differ by a ride-height sensor bracket, ball-joint taper or bushing type. Check the number against the VIN - see how to find an OEM part number.

7. The Most-Searched Numbers on ok.parts

The table below is ranked by repeat searches from registered buyers on ok.parts. This group makes up about 7% of repeat searches among the site's most-searched numbers.

VW / Audi / Skoda / Seat lead with 24% of the group's searches, followed by BMW / Mini (10%), Hyundai / Kia (9%), Ford and Renault / Dacia (7% each) and GM (6%). Febest codes take 5% - buyers looking for a bushing alone - and Sitrak truck numbers 4%. By part name as listed on the site, complete arms take about half of the searches, bushings a little over a quarter, ball joints and knuckles about a tenth each.

Three heavy-truck numbers near the top of the group are listed as arm bushings but are left out of the table. Volvo 20442252, the second most-searched number, is a leaf-spring / axle-bracket rubber mount in aftermarket parts data (also Renault Trucks 7420442252). Sitrak AZ9925688204 is sold as a stabilizer bar bushing; for AZ9925524177, confirm the position on the truck with the supplier. Ask for a dimensioned drawing before ordering any of them.

OEM numberBrandPartOffersMedian priceNotes
8D0407258AMVW / Audi / Skoda / SeatSteering knuckle (wheel bearing housing), front right19$22.55Audi A4 B5, A6 C5, VW Passat B5, Skoda Superb I; 82 mm bearing seat
545014CL1BNissan / InfinitiFront lower control arm, left, stamped steel, with ball joint177$57.08Nissan X-Trail T32, Qashqai J11
31126774826BMW / MiniFront tension strut with mount, right, aluminum143$18.37BMW 5 Series E60 / E61
13401130GM (Chevrolet, Opel, Buick)Front lower control arm, right, aluminum34$26.95Opel / Vauxhall Astra J, Chevrolet Cruze, Volt / Ampera
202000469AACheryFront ball joint, bolt-on33$2.80Chery; also listed for Omoda and Jaecoo
LR024473FordFront lower control arm, left, aluminum274$32.85Range Rover Evoque, Discovery Sport (Land Rover number)
31126852992BMW / MiniFront lower control arm (wishbone), right, aluminum206$11.20BMW 1 Series F20, 2 Series F22, 3 Series F30, 4 Series F32
7L8407152BVW / Audi / Skoda / SeatFront lower control arm, right69$34.19VW Touareg (7L), Porsche Cayenne (first generation), Audi Q7 (4L)
8200839124Renault / DaciaRear suspension link rod with bushings37$6.72Renault / Dacia Duster, Renault Kaptur, Arkana with multi-link rear axle
95032440GM (Chevrolet, Opel, Buick)Front lower control arm (ball joint alone also offered)53$8.21Chevrolet Spark from 2010; superseded by 95319215
1061668FordRear lower lateral link, stamped steel, fits both sides159$3.43Ford Focus I / II, C-Max; also listed for Mazda 3 and Volvo S40 / V50
31126768984BMW / MiniFront tension strut with rubber mount, right, steel56$13.44BMW 3 Series E90 / E91 / E92 xDrive, X1 E84
BB5Z3079AFordFront lower control arm, left47$25.68Ford Explorer, 2011-2012 model years in Ford's parts list
31126775971BMW / MiniFront tension strut, left, aluminum132$18.22BMW 5 Series F10 / F11, 6 Series F06 / F12 / F13
54501M0000Hyundai / KiaFront lower control arm, right213$13.44Hyundai Creta
7L0407021VW / Audi / Skoda / SeatFront upper control arm, aluminum, fits both sides51$13.74VW Touareg (7L), Porsche Cayenne (first generation), Audi Q7 (4L)
54500M0000Hyundai / KiaFront lower control arm, left383$13.44Hyundai Creta
5N0407151VW / Audi / Skoda / SeatFront lower control arm, left, stamped steel, without ball joint163$13.84VW Tiguan I, CC, Passat from 2008
31216792287BMW / MiniSteering knuckle (carrier), front left28$44.80BMW 3 Series F30 / F31; superseded by 31216867735
545303S000Hyundai / KiaFront lower ball joint83$5.23Hyundai Sonata YF, ix35 / Tucson from 2010
7H0407183VW / Audi / Skoda / SeatFront lower control arm bushing, front position110$1.49VW Transporter / Multivan T5 and T6

Find suppliers by part number

Fitment notes are for orientation; confirm every number against the VIN before ordering.

8. Quality: What Separates a Good Part from a Bad One

The arm

  • Process. Ask whether the arm is stamped, forged or cast, and compare with the original. A cast copy of a forged arm is the main risk: it looks right and is less ductile.
  • Weight. A stamped arm clearly lighter than the original means thinner sheet.
  • Welds on stamped arms: continuous, no burn-through at the bushing tube.
  • Coating. Steel arms should be electrocoated (e-coat), not just sprayed. Ask for the salt-spray result and the standard used (ISO 9227 or ASTM B117).
  • Fatigue testing. Ask for the rig-test report.

The ball joint

  • Stud of hardened alloy steel with a smooth ball surface; taper and thread gauged.
  • Pull-out and push-out force tested on samples from each batch.
  • Even turning resistance, no free play, no gritty spots.
  • Boot of chloroprene rubber or a comparable compound, held by retaining rings, with grease inside.

The bushing

  • Rubber hardness (Shore A) to the drawing: too soft gives vague steering, too hard transmits noise and cracks.
  • Bonding: in a destruction test the rubber should tear before it peels cleanly off the metal.
  • Orientation marks on voided and hydraulic bushings.
  • Outer sleeve diameter within tolerance, or the bushing walks out of the arm.

On arrival

Check samples from every lot: left / right marking, coating damage, bushing angle, boot seating, stud threads, hardware included, bearing bore on knuckles. See the quality control guide. Factory certification to IATF 16949 is a useful filter but does not replace sample testing.

9. Wholesale Buying Notes

All figures below are a snapshot of offers on ok.parts taken on 7 October 2026, not a price list.

Price levels. Median offer prices per number ranged from about $1 to $74, with a middle value around $13:

Part typeMedian offer price per numberExamples
Passenger-car bushingsabout $1-57H0407183, TABZZE150B
Ball jointsabout $2-5202000469AA, 545303S000
Rear links, small stamped armsabout $3-71061668, 1K0501529F
Complete front armsabout $11-3554501M0000, 31126774826, LR024473
Steering knucklesabout $11-45517152S000, 8D0407258AM
Heavy-truck bushings and mountsabout $2.50-14AZ9925688204, 20442252

Medians for arm numbers are pulled down by bushings listed under the same number; the top of the range is usually a genuine part. For 31126852992, visible offers ran from about $1 to several hundred dollars.

Who sells. About 87% of the visible offers came from China and 13% from the United Arab Emirates; 86% were from factories, 13% from wholesale companies. Most are unbranded, neutral-pack parts; genuine and Febest-branded parts appear alongside them. See factory or trading company and OEM vs OES vs aftermarket.

MOQ. The most common minimums were 1, 10, 20, 50, 100 and 200 pieces.

Packaging and freight. Each piece should be bagged and boxed so that boots are not crushed and coatings do not rub through. Arms and knuckles are heavy, so freight is a real share of landed cost; see the Incoterms guide.

Customs. Control arms and ball joints are normally declared under HS subheading 8708.80 (suspension systems and parts). National sub-codes differ, and loose rubber-metal bushings may be classified elsewhere - check with your broker.

Warranty. Agree in writing what counts as a defect (bond separation, boot failure, play within a stated period) and what does not (wrong installation, impact damage).

Combining an order. A sensible first order per vehicle model is the full set: left and right arms, separate bushings and ball joints, stabilizer links and tie rod ends. On ok.parts, search each OEM number and compare price, MOQ, lead time, supplier country and rank on the offer page before opening supplier contacts.

Post a buying request

10. Frequently Asked Questions

Should I stock complete arms or separate bushings and ball joints?

Both. Where labor is expensive, workshops prefer complete arms because fitting is faster. Price-sensitive markets and owners of cars with expensive aluminum arms buy the bushing or ball joint alone.

Why do prices under one OEM number range from $1 to more than $100?

Suppliers list the bare bushing, the ball joint, an unbranded complete arm and the genuine part under the same number.

How can I tell a hydraulic bushing from a solid one?

Not reliably from a photo. Ask the supplier to confirm it in writing; a hydro-bushing has fluid chambers inside, and cutting one sample from the batch settles it.

Do control arms have to be replaced in pairs?

It is not mandatory, but it is good practice on one axle: a new bushing is stiffer than a worn one on the other side. Stock left and right together.

Why did a new bushing tear after a few months?

Most often installation: the pivot bolts were tightened with the wheels hanging, so the rubber is twisted at ride height. A wrong pressing angle and poor rubber-to-metal bonding are the other causes.

Related Guides