Engine Mounts: Types, Failure Symptoms and Wholesale Sourcing Guide
On ok.parts, engine and gearbox mounts are searched under generic listing names - Engine Mount (31% of searches in the group), Support Assy (30%), Support Sub-Assy (25%) and Insulator (10%) - and the same names also cover strut top mounts, bump stops, gas struts and truck cab dampers. The name tells you little; the number tells you what the part is.
Mounts are easy to copy and hard to judge from a photo. An original and a copy under the same number can look alike and still differ in what the driver feels: the hardness of the rubber, the bond between rubber and metal, and whether there is fluid inside at all.
- What Engine and Gearbox Mounts Do
- Mount Designs: Solid Rubber, Hydraulic, Switchable, Active
- Where the Mounts Sit: Right, Left, Front, Rear
- How Mounts Fail and What to Replace Together
- Reading the Number and Avoiding Wrong Orders
- The Most-Searched Numbers on ok.parts
- Strut Top Mounts and Other Parts Behind the Same Names
- Quality: Rubber, Bonding, Fluid and Brackets
- Wholesale Buying Notes
- Frequently Asked Questions
Right-hand engine mount 50820SNBJ02 for the eighth-generation Honda Civic: steel bracket, rubber body, aluminum base. The bracket carries the QF mark of QUATTROFRENI, the private label of ok.parts.
1. What Engine and Gearbox Mounts Do
A powertrain mount has three jobs. It carries the weight of the engine and gearbox, holds them in position against drive torque, braking and cornering forces, and keeps engine vibration out of the body.
Isolation wants a soft mount: at idle the engine shakes with small, fast movements, and soft rubber does not pass them on. Control wants a stiff, well-damped mount: when the car pulls away, changes gear or hits a pothole, the powertrain makes large, slow movements that must be stopped quickly. Every design is a compromise between the two, and the expensive designs exist to get both at once.
Most cars use three or four mounts, each tuned for its place and for the engine and gearbox it carries.
2. Mount Designs: Solid Rubber, Hydraulic, Switchable, Active
| Type | How it works | Watch for |
|---|---|---|
| Solid rubber | Rubber bonded between metal parts | Rubber hardness, bonding |
| Hydraulic | Rubber spring plus fluid chambers joined by a channel | Leaks, solid-rubber copies |
| Switchable hydraulic | Vacuum or a solenoid changes the stiffness at idle | Port or connector, function |
| Active | An actuator produces counter-vibration; used on some engines with cylinder deactivation | Electronics, proven source |
Solid rubber (rubber-metal) mounts. Stiffness is set by the compound and the shape: voids and ribs make the same mount soft in one direction and stiff in another, so it must be installed the right way round.
Hydraulic mounts, also called hydro mounts. Inside the rubber body are two chambers filled with a glycol-based fluid, separated by a plate with a long narrow channel and usually a loose membrane. Small, fast vibrations only move the membrane, so the mount stays soft. Large, slow movements push fluid through the channel, which damps the bouncing of the engine on its mounts.
Switchable mounts add a valve. At idle a bypass or an air chamber is opened, by vacuum or by a solenoid, and the mount becomes softer than a fixed hydraulic design. Look for a vacuum nipple or an electrical connector. Audi A6 mount 4F0199379BH is of this kind: aftermarket makers list it as an electrically adjustable hydro mount.
3. Where the Mounts Sit: Right, Left, Front, Rear
Transverse engine, pendulum layout. Two load-bearing mounts sit high up, one on the engine side and one on the gearbox side. A torque rod low down links the powertrain to the subframe and takes the rotation. On most transverse layouts the engine is on the right and the gearbox on the left, so "right mount" usually means the engine-side mount and "left mount" the gearbox-side mount; some layouts are mirrored.
Transverse engine, four-point layout. Many Hyundai, Kia, Mitsubishi and Toyota models have a front and a rear mount low on the subframe in addition to the two side mounts. Hyundai, Kia and Mitsubishi call them roll stoppers; Toyota calls all four insulators.
Longitudinal engine. Rear-wheel-drive cars and most ladder-frame pickups and SUVs: one mount on each side of the engine and a gearbox mount on a crossmember.
Left and right are given in the direction of travel, on left-hand-drive and right-hand-drive cars alike.
4. How Mounts Fail and What to Replace Together
- Cracked or torn rubber. Age, heat and ozone harden the rubber until it cracks.
- Debonding. The rubber peels off the metal.
- Sagging. The rubber settles and the engine sits lower.
- Fluid leak. A hydraulic mount whose rubber has split loses its fluid and leaves a dark, oily stain on the mount and below it.
- Oil damage. Engine oil or power-steering fluid dripping on a mount softens and swells natural rubber. Fix the leak first - often a valve cover gasket, see valve covers and oil separators - or the new mount goes the same way.
What the driver notices: vibration in the steering wheel, seat and body at idle; a thump when pulling away, shifting or lifting off the throttle; knocking over bumps.
Passive mounts set no fault codes. On switchable and active mounts the control unit can store a fault code for the solenoid or actuator circuit.
Replace at the same time
- Inspect the whole set: when one mount fails, the others have carried its share.
- On longitudinal engines, change left and right engine mounts as a pair.
- Fit new bolts where the manufacturer specifies them; some makers treat mount bolts as single-use.
5. Reading the Number and Avoiding Wrong Orders
The number often tells the position. Toyota uses the first five digits for the part type: 12361 is the front insulator, 12371 the rear, 12372 the left one. So 1236102100, 1237122220 and 1237222150 are a front, a rear and a left mount before you look anything up. Hyundai and Kia use 21910 for the front roll stopper on models that have one, as in 219101G200, and 54610 for the front strut top mount. In VW group numbers the middle block 199 marks the powertrain mounting; in BMW numbers the leading 2211 marks the engine suspension group. More formats are in how to find and read an OEM part number.
Left and right. BMW mounts 22116768852 (right) and 22116768853 (left) differ by one digit and look the same in a photo. Check the labels on arrival.
Engine and gearbox variants. Petrol and diesel, manual and automatic versions of one car often share the bracket and differ in rubber hardness or hydraulic tuning. Match by VIN, not by appearance.
Several numbers for one part. Ford issues a new number when a part is revised. Aftermarket makers cross-list Focus mount 1306038 with several other Ford numbers, 1345658 and 1430067 among them. That is a cross-reference, not Ford's own replacement record, so confirm by VIN.
Scope of supply. A torque rod can be offered complete, without its bracket, or as the bare bush. Ask for a photo of what is in the box.
6. The Most-Searched Numbers on ok.parts
The table lists the powertrain mounts of the group, ranked by repeat searches from registered buyers on ok.parts. Strut top mounts and the other parts found under the same listing names are left out of it; they are covered in the next section.
Across the whole name group, VW group numbers lead with 14% of searches, followed by GM and Toyota / Lexus at 11% each and Hyundai / Kia at 10%. Those shares cover everything behind the generic names, not only powertrain mounts.
Among the true powertrain mounts, demand goes to plain parts of high-volume cars: roll stoppers for the Hyundai Accent and the Mitsubishi Lancer, the mounts of the Toyota Corolla, the Honda Civic side mount, the VW Golf torque rod. Hydraulic mounts for Audi and BMW follow at higher prices.
| OEM number | Brand | Part | Offers | Median price | Notes |
|---|---|---|---|---|---|
| 8941119031 | Isuzu | Engine mounting rubber cushion | 7 | $11.14 | Application not verified; check by VIN |
| 219101G200 | Hyundai / Kia | Front roll stopper (torque mount) | 8 | $5.45 | Hyundai Accent / Verna 2006-2011 |
| 50820SNBJ02 | Honda / Acura | Engine side mount, right, hydraulic | 36 | $11.20 | Honda Civic 2006-2011 (8th generation) |
| 1171065J00 | Suzuki | Rear engine mounting | 17 | $7.76 | Suzuki Grand Vitara / Escudo from 2005 |
| MN101572 | Mitsubishi | Rear roll stopper | 31 | $5.38 | Mitsubishi Lancer from 2007, Outlander, ASX |
| 4F0199379BH | VW / Audi / Skoda / Seat | Hydraulic engine mount, left, electrically switchable | 18 | $26.88 | Audi A6 (C6) 2004-2011 |
| 1807HA | Peugeot / Citroen | Rubber-metal bush of the right engine mount, not the complete mount | 24 | $3.36 | Peugeot 307, 308, 407, Partner; Citroen C4, C5, Berlingo |
| 1237222150 | Toyota / Lexus | Left (gearbox side) mount | 51 | $8.21 | Toyota Corolla, Auris (E150) from 2006 |
| 22116775906 | BMW / Mini | Hydraulic engine mount, right | 37 | $18.29 | BMW 5 Series (F07/F10/F11), 7 Series (F01/F02) |
| 1236102100 | Toyota / Lexus | Front engine mount | 42 | $4.18 | Toyota Avensis 1997-2003 |
| 1236136130 | Toyota / Lexus | Front engine mount | 52 | $28.45 | Toyota RAV4 2.5, 2013-2018 |
| 1306038 | Ford | Right engine mount, hydraulic | 48 | $10.82 | Ford Focus, C-Max |
| 1237122220 | Toyota / Lexus | Rear engine mount | 47 | $6.79 | Toyota Corolla, Auris (E150) from 2006 |
| 1K0199855BA | VW / Audi / Skoda / Seat | Lower torque rod (pendulum support) | 27 | $4.48 | VW Golf V / VI family; check version by VIN |
| 95133816 | GM (Chevrolet, Opel, Buick) | Engine mount, right | 12 | $12.24 | Chevrolet Sonic / Aveo (T300), 1.4 and 1.8 petrol |
| 22116768853 | BMW / Mini | Hydraulic engine mount, left | 54 | $10.81 | BMW 1 Series (E81-E88), 3 Series (E90-E93), X1 (E84), Z4 (E89) |
| 22116768852 | BMW / Mini | Hydraulic engine mount, right | 54 | $10.81 | BMW 1 Series (E81-E88), 3 Series (E90-E93), X1 (E84), Z4 (E89) |
Fitment notes are a guide for sorting stock, not a substitute for a VIN check.
7. Strut Top Mounts and Other Parts Behind the Same Names
A quarter of the searches in this group go to "Support Sub-Assy", and most of the top-ranked numbers under that name are strut top mounts. A strut top mount is a suspension part: it fixes the top of the strut to the body and, on the front axle, lets the strut turn with the steering through a bearing. The bearing is either built into the mount or supplied separately. Among the most-searched are Hyundai 546103X200 (Elantra from 2010, Veloster) and 5461025000 (Accent 2000-2005, Getz), Renault 540340002R (Megane III, Scenic III) and Nissan 54320JD00B (Qashqai, right side; the left one has its own number).
Strut mounts are replaced in pairs per axle, normally with the shock absorbers. These parts carry suspension loads, so do not treat the cheapest offer as equal to the original: check the rubber bonding, the stud threads, and whether a bearing is part of the offer. Related chassis parts: control arms and bushings and tie rod ends and stabilizer links.
Other parts that appear under the same listing names:
- Truck cab parts. DAF 1817662, the most-searched number of the whole group, is a cab suspension shock absorber; the top MAN and Scania numbers are a cab damper and a gas spring.
- Gas struts. LR049207 is a bonnet gas strut for the Range Rover.
- Brackets. VW group 1K0253144BD, listed as "Mounting", is a bracket from the exhaust group.
- Bump stops, dust boots and spring seats. Most of the top "Insulator" rows, for example the Hyundai / Kia upper spring seat 546202K000.
- Brake caliper brackets, listed as "Support Brake Caliper" - see the brake calipers guide.
Offer titles are just as loose: the Renault strut mount is titled both "Strut Mount" and "Engine Mount". Go by the number and the photo.
8. Quality: Rubber, Bonding, Fluid and Brackets
Rubber compound. Natural rubber is the standard material for powertrain mounts because of its fatigue life. Its weak points are oil, heat and ozone. Hardness is given in Shore A and measured with a durometer (ASTM D2240, ISO 48-4). A copy that is too hard passes every visual check and vibrates in the car; one that is too soft sags. Ask the factory for the hardness specification and tolerance, and measure samples yourself.
Bonding. The metal parts are cleaned, coated with primer and adhesive, and the rubber is vulcanized onto them in the mold. A good bond is stronger than the rubber: when a sample is torn apart, rubber stays on the metal. Bare metal means a bonding failure. ASTM D429 describes the adhesion tests.
Hydraulic function. The common shortcut is a solid rubber body in a housing that looks hydraulic. It bolts in, costs less, and the car vibrates at idle. Checks that work:
- Weigh samples against an original. The BMW mounts 22116768852 and 22116768853 weigh about 0.9 kg each; a clearly lighter copy is suspect.
- Cut one sample open. There must be fluid, a partition plate and a membrane.
- Ask for test data next to that of an original part: load-deflection curve, dynamic stiffness and damping against frequency, durability under cyclic load.
- Ask whether every unit is leak-tested.
Brackets and housings. Die-cast aluminum must be free of porosity and cracks around the bolt holes; stamped steel needs sound welds and a coating that holds up in salt spray (ISO 9227). A mount that has to be forced into place is preloaded from the first day.
Incoming inspection
- Number, side marking and production date on every part.
- Hole positions, stud threads and overall height against the reference sample.
- Hardness on several pieces per batch.
- A pry test at the rubber edge: no lifting from the metal.
- Hydraulic mounts: weight, no oily film in the bag.
Rubber ages in storage: keep mounts cool and dark and rotate stock by production date. See also the quality control guide.
9. Wholesale Buying Notes
Prices. In the snapshot of 7 October 2026, median offer prices were about $4 to $8 for solid rubber mounts and roll stoppers (219101G200, MN101572, 1K0199855BA, the Toyota Corolla mounts) and about $10 to $18 for hydraulic mounts (Honda 50820SNBJ02, Ford 1306038, the BMW mounts). The switchable Audi mount stood at about $27. RAV4 front mount 1236136130 stood at about $28; more than half of its visible offers came from the United Arab Emirates, and Toyota-branded parts were among them. Strut top mounts were at about $3.50 to $6. An offer far below the median of its number may be a bare bush, a part without its bracket, or a solid copy of a hydraulic mount.
Suppliers. About 84% of the visible offers came from China and 16% from the United Arab Emirates; 84% were posted by factories and 16% by wholesale companies. Most offers are unbranded, neutral-pack parts; offers under the car maker's brand or an aftermarket brand appear on many numbers. See OEM vs OES vs aftermarket and factory or trading company.
MOQ. Most numbers have offers with a minimum of 1 piece; the usual volume steps are 20, 30, 50, 100 and 200 pieces.
Order in vehicle sets. Workshops want the right mount, the left mount and the torque rod for one car.
Packing and freight. Each mount needs its own box with the number and side on the label. Mounts are heavy for their price, so sea freight is the normal route; see shipping auto parts from China and Incoterms for importers. Aftermarket makers declare rubber-to-metal mounts under HS 4016.99 (articles of vulcanized rubber) or 8708.99 (vehicle parts); practice and national sub-codes differ, so confirm the code with your broker.
Warranty. Agree in writing what counts as a defect - debonding, fluid leak, cracked bracket - and for how long.
On ok.parts you compare offers for one number side by side and open contacts per supplier. If no offer suits, post a buying request.
10. Frequently Asked Questions
Can a solid rubber mount replace a hydraulic one?
It will bolt in, and some low-priced copies are built this way. The car will have more vibration and noise, because the fluid damping is missing. Sell such a part as what it is, not as an equivalent.
How can I tell whether a hydraulic mount really has fluid inside?
Compare its weight with an original part, and cut open one sample from each new supplier. A real hydraulic mount has fluid, a partition plate with a channel and a membrane.
Should all mounts be replaced at once?
Not necessarily, but inspect the whole set: the remaining mounts have carried extra load. On longitudinal engines the left and right engine mounts are normally changed as a pair.
Are left and right mounts interchangeable?
As a rule, no. They are often mirror images with consecutive numbers, such as BMW 22116768852 and 22116768853, or they differ in stiffness.
Is a strut top mount an engine mount?
No. It is a suspension part that fixes the top of the strut to the body. It appears next to engine mounts only because both are listed under generic names such as Support Sub-Assy.
Related Guides
- Control Arms, Bushings and Ball Joints: Technical and Wholesale Sourcing Guide
- Tie Rod Ends, Inner Tie Rods and Stabilizer Links: Wholesale Sourcing Guide
- Valve Covers, PCV Membranes and Oil Separators: Wholesale Sourcing Guide
- Auto Parts Quality Control in China - The Complete Inspection Guide
- OEM vs OES vs Aftermarket vs Genuine Parts: What Is the Difference
- How to Find and Read an OEM Part Number: Formats by Car Brand
- Factory or Trading Company? How to Verify a Chinese Auto Parts Supplier