Tie Rod Ends, Inner Tie Rods and Stabilizer Links: Wholesale Sourcing Guide

Tie rod ends, inner tie rods, stabilizer links and stabilizer bushings are among the cheapest chassis parts a wholesaler stocks and among the easiest to order wrong: two parts that look identical on a photo can differ by one thread pitch, a few millimeters of length or one millimeter of bar diameter.

Tie rods steer the wheels and are safety-critical: a stud that pulls out of its housing means loss of steering on that wheel. Stabilizer links and bushings only control body roll; when they wear, the car gets noisy long before it gets dangerous. That difference should decide how much checking each purchase gets.

58%of searches: tie rod parts
14%Ford, the largest brand share
$2.26middle median offer price, Oct 2026
77%of visible offers from China

Outer tie rod end 1J0422812B with the letter R on the housing

Outer tie rod end 1J0422812B for the VW Golf IV; the R on the housing marks the right-hand part - see offers

1. What These Parts Do

On a rack-and-pinion steering gear, each end of the rack carries a tie rod that pushes and pulls the steering knuckle. It is made of two ball joints screwed together:

  • the inner tie rod - also listed as axial joint, axial rod or rack end - screws onto the end of the rack and lets the rod swing as the suspension moves;
  • the outer tie rod end screws onto the inner rod and sits with its stud, usually tapered, in the steering arm of the knuckle.

The thread between the two, held by a lock nut, is the toe adjustment of that wheel.

The stabilizer bar (anti-roll bar, sway bar) is a torsion spring that ties the left and right wheel of one axle together and resists body roll. Stabilizer bushings clamp the bar to the subframe or body and let it rotate. Stabilizer links (sway bar links, drop links, end links) connect the bar ends to the strut or the control arm.

2. Types and Designs

Outer tie rod end
Outer tie rod end
Ball joint in a forged housing, in most designs with an internal thread for the inner rod, and a stud for the knuckle. Straight or angled; angled housings are side-specific.
Most searched
Inner tie rod (axial joint)
Inner tie rod (axial joint)
Ball joint that screws onto the rack end, with a long rod threaded for the outer end. Works hidden under the rack boot.
Under the boot
Stabilizer link
Stabilizer link
Rod with a joint at each end between the stabilizer bar and the strut or control arm.
Replaced in pairs
Stabilizer bushing
Stabilizer bushing
Rubber mount that clamps the bar to the subframe. Ordered by the bar diameter it fits, not by the car model alone.
Diameter-critical

Shown, in order: tie rod end 1J0422812B, an inner tie rod listed under Geely number 4036028500, front stabilizer link LR002626 for the Land Rover Freelander 2 and the VW group front bushing 6Q0411314R. Several of the photos carry the mark of QUATTROFRENI, the private label of ok.parts.

Ends, inner rods and assemblies

Some suppliers offer the inner and outer part pre-assembled as a tie rod assembly. Listings use the terms loosely: on ok.parts the generic name "Rod Assy Tie" is attached to outer ends as well as to complete rods. Read the offer title and the photo before comparing prices.

Stabilizer link designs

DesignConstructionWhere it is common
Ball joint at both endsSteel rod, two sealed ball joints, studs parallel or at an angleFront axles with the link on the strut; many rear axles
Ball joint and bushing endOne ball joint, one bolt-through end with rubber bushingsRear axles, some front lower arms
Bolt and bushingsLong bolt, spacer sleeve, cup washers, rubber or polyurethane bushingsOlder designs, pickups, body-on-frame 4x4s
Composite bodyGlass-fiber-reinforced plastic body with molded-in ball jointsOriginal equipment on some modern cars
Two ball joints on a short rod, supplied with flange nuts: Nissan rear link 56261AV611
Two ball joints on a short rod, supplied with flange nuts: Nissan rear link 56261AV611
Ball joint at one end, bolt-through bushings at the other: Hyundai Accent rear link 5583025000
Ball joint at one end, bolt-through bushings at the other: Hyundai Accent rear link 5583025000
Studs set at an angle to each other: Chery rear link M112916030
Studs set at an angle to each other: Chery rear link M112916030

Most stabilizer bushings are a single rubber molding with a slit, so that they can be opened and pushed over the bar. Some have a fabric or low-friction lining in the bore, and some are bonded to the bar at the factory.

3. How They Fail and How to Check Them

All ball joints in this group fail the same way. The rubber boot cracks or is cut, water and grit get in, the grease washes out, the ball and its plastic seat wear, and play develops. A joint with a torn boot will need replacing even if it is still tight.

Worn tie rod ends and inner tie rods show up as vague steering, a light knock on rough roads and uneven tire wear. Check with the wheel off the ground: grip it at the 3 and 9 o'clock positions and rock it while watching the joints. Play at the inner joint is felt through the rack boot; a split boot is replaced together with the rod.

Stabilizer links rattle or knock over small bumps at low speed. Check them by hand with both wheels of the axle at the same height, so that the bar is not twisted and holding the joints tight.

Stabilizer bushings that have hardened or worn squeak over speed bumps and may let the bar knock in its clamps. Links and bushings are normally replaced in axle pairs.

These parts are purely mechanical and set no diagnostic trouble codes. Three fitting points for workshop customers:

  • After any tie rod work the toe must be set on an alignment rig; counting threads is only good enough to drive there.
  • Self-locking nuts are used once. The stud is separated with a puller, not a hammer.
  • Rubber bushings are not smeared with mineral grease.

4. What Separates Look-Alike Parts

Six things cause most wrong orders in this group.

1. Left and right. Straight tie rod ends often fit both sides. Angled ones do not: the housing is a mirror image, and many are marked L or R on the housing, as in the photo at the top. Nissan gives the two sides different basic numbers: on the Micra, 48640AX600 is the left end and 48520AX600 the right.

2. Thread direction. On linkages adjusted by turning a tube or sleeve, one end has a right-hand and the other a left-hand thread, under different numbers.

3. Thread size and pitch. The thread between inner rod and outer end is usually a fine-pitch metric thread, and two versions of the same car can differ only in pitch or in one size step.

4. Stud taper. A tapered stud must seat in the knuckle over its full length. Compare the diameter at the large end and the taper length with the old part or the drawing.

5. Steering gear version. The same car model can be built with racks from different manufacturers, or with hydraulic and electric power steering, and the inner tie rods then differ in thread or length. Ask for the VIN or the number on the old part - see reading a VIN and finding an OEM number.

6. Bar diameter, axle and link length. Carmakers fit bars of different diameters to the same body depending on engine and suspension package, in steps as small as one millimeter, and each needs its own bushing. Front and rear bushings of one model also look alike. For links, what matters is the length between ball centers, the stud threads and the angle between the two studs.

Threaded end of an inner tie rod with lock nut and wrench flats

Adjusting thread, lock nut and wrench flats of inner tie rod 4036028500. Thread diameter and pitch are the first things to check on a sample - see offers

5. Reading the Part Number

Several carmakers build the type of part into the number. The patterns below hold for most models, so a listing whose description contradicts the number deserves a second look.

BrandPatternMeaning
Toyota / Lexus45503, 48815, 48820, 48830Steering rack end; front stabilizer bushing; front link; rear link
Nissan / Infiniti48520 and 48640, 54613, 56261Outer tie rod ends; stabilizer bushing, usually front; rear link
Hyundai / Kia54830, 55530 or 55830Front stabilizer link; rear stabilizer link
Mazdamiddle group 32, 34 or 28Steering; front suspension; rear suspension
Peugeot / Citroen3812, 3817, 5087Inner tie rod; outer tie rod end; stabilizer link
Chinese brandsgroup 2906 or 2916Front stabilizer; rear stabilizer

Nissan 54613, for example, is the front bushing on most models, yet 54613JD17A is listed by Nissan as the rear stabilizer bushing of the Qashqai.

In VW group numbers the first digit of the middle group gives the main assembly group, 4 for front axle and steering and 5 for rear axle: 5Q0505465C is a rear-axle part, 6Q0411314R a front-axle part. On tie rod ends the digits 811 and 812 before the suffix letter mark left and right. Ford and GM numbers carry no such information. Chinese carmakers mostly use a common group-number scheme, so the JAC bushing 2906231U3400 can be placed at the front stabilizer from its first four digits; more in the guide to parts for Chinese car brands.

Some carmakers supply the bushings only together with the bar, often because they are bonded to it, and aftermarket repair bushings are then listed under the bar number. The VW number 5Q0411303R is such a case: it is the number of a complete front stabilizer bar, but the offers under it are repair bushings priced well under one dollar.

Two-piece split stabilizer repair bushing

A two-piece repair bushing listed under 5Q0411303R - see offers

6. The Most-Searched Numbers on ok.parts

The table is ranked by repeat searches from registered buyers on ok.parts.

No brand dominates. Ford has the largest share of searches in the group at 14%, followed by the VW group (11%), Mitsubishi (10%) and Toyota / Lexus (9%). A stock list for this group has to be wide rather than deep.

Steering outweighs the stabilizer: tie rod ends, assemblies and inner rods together account for about 58% of the searches, stabilizer links for 22% and bushings for about 21%. Yet the single most-searched number is a bushing, Mitsubishi MN100250. Chinese-brand numbers are in the list too: a Geely tie rod end is in second place, and Chery numbers appear further down.

OEM numberBrandPartOffersMedian priceNotes
MN100250MitsubishiFront stabilizer bar bushing36$1.23Mitsubishi Lancer, Outlander
4036036100GeelyOuter tie rod end15$2.24
4882060090Toyota / LexusFront stabilizer link9$1.91Toyota 4Runner from 2010, Land Cruiser Prado
K12332280MazdaOuter tie rod end37$11.16Mazda CX-5
54613JD17ANissan / InfinitiRear stabilizer bar bushing90$7.85Nissan Qashqai. Mixed offers - check the title
4056A230MitsubishiRear stabilizer bar bushing63$0.67Mitsubishi Outlander
1433273FordOuter tie rod end, right19$2.76
4881530040Toyota / LexusFront stabilizer bar bushing67$3.26Toyota Carina E, Caldina
5Q0505465CVW / Audi / Skoda / SeatRear stabilizer link42$2.17MQB platform: VW Golf VII, Audi A3 (8V), Skoda Octavia III
13327928GM (Chevrolet, Opel, Buick)Front stabilizer link52$1.94
1471446FordFront stabilizer link76$1.42
4550339275Toyota / LexusSteering rack end (inner tie rod)254$4.51Toyota Camry. Mixed offers - check the title
4881065J00SuzukiOuter tie rod end38$2.28Suzuki Grand Vitara / Escudo
96391875GM (Chevrolet, Opel, Buick)Front stabilizer link125$1.79
3812E5Peugeot / CitroenInner tie rod (axial joint)5$1.92
4056A121MitsubishiFront stabilizer bar bushing89$0.62Mitsubishi Pajero / Montero
4422A052MitsubishiOuter tie rod end84$2.44Mitsubishi Outlander, ASX
4883032010Toyota / LexusRear stabilizer link33$1.19Toyota Corona, Carina, Caldina
6001549311Renault / DaciaFront stabilizer bar bushing121$0.69Dacia Logan, Sandero, Dokker, Lodgy
51306SEAE02Honda / AcuraFront stabilizer bar bushing41$4.04Honda Accord sedan (CL7 series)
1851900FordFront stabilizer link170$1.42Ford Focus from 2011, Kuga
1J0422812BVW / Audi / Skoda / SeatOuter tie rod end, right98$1.91VW Golf IV, Bora, New Beetle

Vehicle notes name main models only and are not complete application lists; confirm every number against the vehicle or the VIN before ordering. Two Ford numbers further down the ranking, 1541652 and 1894033, lead to the same set of offers on ok.parts; an aftermarket cross-reference lists both as the same right-hand tie rod end.

Find suppliers by part number

7. Quality: Materials, Tests and Inspection

What a good joint is made of

  • Ball stud: forged, heat-treated alloy steel with a finely finished ball. The finish decides how fast the seat wears.
  • Housing: forged steel, closed by rolling or pressing its edge over a cover. This closure holds the stud in under load.
  • Seat: a plastic bearing shell, preloaded so that the joint moves with even resistance and no play.
  • Boot: a rubber compound that stays elastic in cold and resists ozone and grease.

For bushings the material is the product: the rubber compound, its Shore A hardness, its compression set after heat aging and the accuracy of the bore.

What to ask the factory for

  1. Material and heat-treatment specification of the stud, with hardness records.
  2. Test reports for stud pull-out and push-out force, rotating and tilting torque, play under load and endurance, with acceptance limits.
  3. Salt spray results for the coating; ozone and low-temperature results for the boot.
  4. Proof of a working quality system - IATF 16949 at a factory that supplies carmakers - and a batch code on every part.

See also quality control and inspection in China and factories and trading companies.

What to inspect on arrival

  • Move every sampled joint by hand: it should turn and tilt with even resistance. A stud that flops under its own weight has no preload; a gritty one has dirt or a damaged seat inside.
  • Check boots for cuts, loose retaining rings and leaking grease.
  • Run a nut down the stud threads; check the internal thread of tie rod ends with a gauge or a sample inner rod.
  • Measure length, thread and taper against the reference sample, and bushing bores with a plug gauge.
  • Confirm that left and right are marked and not mixed in the cartons.
Play, torque and pull-out strength cannot be judged from a photo or a price. A cheap tie rod is not equivalent to the original part until samples have been measured and, if the volume justifies it, pull-tested by an independent lab.

8. Wholesale Buying Notes

At the time of writing (snapshot of 7 October 2026), median offer prices for the most-searched numbers of this group on ok.parts ranged from about $0.45 to about $19 per piece, with a middle value of about $2.25. By sub-type:

Part typeTypical median offer priceWhere genuine-brand offers dominate
Stabilizer bushingabout $0.45 to $1.25$3 to $8
Stabilizer linkabout $1.20 to $2.50about $14 on one Nissan number
Outer tie rod endabout $1.90 to $2.80$4 to $19
Inner tie rodabout $1.90 to $4.50-

These are medians of visible offers, not quotes. Ranges under a single number are often very wide: genuine, branded aftermarket and unbranded factory parts sit side by side, and cross-linked listings bring in other parts altogether. An offer at $200 under a stabilizer bushing number is a different part, not an expensive bushing.

About three quarters of the visible offers came from China and about one quarter from the United Arab Emirates; roughly three quarters were from factories and the rest from wholesale companies. The most common minimum order quantities were one piece and 50 to 500 pieces per number, with up to 1,000 on some bushings. Typically the one-piece offers are genuine or branded parts at a higher unit price, and the larger quantities are unbranded or neutral-pack factory parts.

  • Mix numbers in one order. Combine tie rod ends, inner rods, links and bushings for the same vehicles with control arms and ball joints.
  • Packaging. Tie rod ends and links should be boxed individually with their nuts; bushings usually ship in bags. For your own brand see private label manufacturing.
  • Genuine or not. Offers that claim a carmaker's brand at a factory price deserve a second look - see OEM, OES and aftermarket parts and counterfeit parts.
  • Customs and freight. These are parts of HS heading 8708 (parts and accessories of motor vehicles), where steering parts are grouped under 8708.94 and suspension parts under 8708.80. Classification of an individual item and the national sub-codes differ, so confirm with your broker. See shipping from China and Incoterms.

Post a buying request

9. Frequently Asked Questions

What is the difference between an outer tie rod end and an inner tie rod?

The outer tie rod end is the ball joint at the wheel side, with its stud in the steering knuckle. The inner tie rod, also called axial joint or rack end, screws onto the steering rack and carries the adjusting thread for the outer end.

Are left and right tie rod ends the same part?

Straight ends often are; angled ends are not, and they carry different part numbers and usually an L or R marking.

How do I choose the right stabilizer bushing when several are listed for one car?

By axle and by the diameter of the stabilizer bar. Measure the bar where the bushing sits, or use the number molded into the old bushing, and match it to the bore of the new one.

Can a steel stabilizer link replace an original plastic one?

Usually yes, provided the length between ball centers, the stud threads and the stud angles are the same. Fit the same type on both sides of the axle.

Is wheel alignment needed after replacing these parts?

After a tie rod end or an inner tie rod, always, because the toe setting is disturbed. Stabilizer links and bushings do not affect wheel geometry.

Related Guides